Search found 93 matches
- Mon Mar 18, 2024 8:55 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Which Fairing Bolts
- Replies: 22
- Views: 6634
Re: Which Fairing Bolts
There are 3 screws that are longer without shoulders in each engine fairing starting with the 2019 and usually no screw on the tank cover forward point under the each side glove box. On the Torque Sheet, the new value for the rear Brake Caliper is 28Nm vs 24Nm. I may make a completely NEW version of...
- Mon Feb 26, 2024 2:28 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Brake Fluid
- Replies: 6
- Views: 813
Re: Brake Fluid
It is actually DOT4 LV (Low Viscosity). This is what is specified now for bikes back as far as early 1990’s R-series as well as others. What’s stamped on the reservoir cap won’t be updated, but specifications from BMW are changed from time to time. You can keep up to date with your particular model ...
- Wed Dec 20, 2023 10:41 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Body panel screws
- Replies: 7
- Views: 1465
Re: Body panel screws
Looks like a solution.
- Mon Jul 24, 2023 1:18 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Which Fairing Bolts
- Replies: 22
- Views: 6634
Re: Which Fairing Bolts
If you have a WetHead 1200, this shop aid will help. It keeps your screws from being lost and reminds you of not putting back all the screws and where they should go if you have some left over on reassembly. I take this file to my local FedEx Office printing location and have them print it out 12x18...
- Sun Jul 23, 2023 10:30 am
- Forum: Maintenance, Servicing and Problems
- Topic: 12,000 mile service due
- Replies: 11
- Views: 1076
Re: 12,000 mile service due
- Tue Jul 18, 2023 9:29 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Valve clearance
- Replies: 10
- Views: 1466
Re: Valve clearance
With the range being 0.10mm for both the Intake and Exhaust, and the hemispherical shims only available in 0.05mm spacing...that means that only 1 size shim will put in the range...a second incremental step in shims will put you outside the acceptable area the other way. Hope that makes sense and an...
- Mon Jul 17, 2023 3:48 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Valve clearance
- Replies: 10
- Views: 1466
Re: Valve clearance
The procedure for doing the Cam Timing on the 1200 CamHead engine is very similar to what I do frequently on the 1200/1250 WetHead/ShiftHead. You need to set and lock the flywheel/crankshaft at TDC with a specific pin that fits in an open hole on the RH side of the rear of the engine block. The side...
- Mon Jul 03, 2023 2:03 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Valve clearance
- Replies: 10
- Views: 1466
Re: Valve clearance
I would change 5 of the 8 shims. Both of the 0.41mm clearance EXH. valves would be set to a good value of 0.36mm. The other EXH now at 0.38mm would be at 0.33mm, making it nearer to the tighter end of the range. Of course the 0.23mm INT would be at 0.18mm, a reasonable number closer to the middle an...
- Mon Jul 03, 2023 2:08 am
- Forum: Maintenance, Servicing and Problems
- Topic: Valve clearance
- Replies: 10
- Views: 1466
Re: Valve clearance
I would say that if it's outside the specification, it should be adjusted...if it's at the limit of the spec, and you are already replacing some of the shims to replace the one that's at 0.23mm as well. If money was not a factor, I'd put all of the clearances at 1/3 of the range of tolerances. So fo...
- Mon Jun 12, 2023 3:13 pm
- Forum: Maintenance, Servicing and Problems
- Topic: 1250 Caliper bolt torque
- Replies: 3
- Views: 869
Re: 1250 Caliper bolt torque
Direct from the Updateable Repair Manual R Models K5X Official DVD (not a copy): Radial brake caliper on telescopic forks (M10x65 bolt) 38NM (Note: no mention of using thread locker) Brake caliper to bevel gears (Long threaded dome to bevel gears M8x30 bolts) 28Nm Replace screw. Thread-locking compo...
- Mon Oct 17, 2022 1:49 pm
- Forum: Newbies
- Topic: New R1200RT Owner
- Replies: 7
- Views: 587
Re: New R1200RT Owner
Deleted
- Wed Aug 17, 2022 2:36 pm
- Forum: Tools
- Topic: Cam tools.
- Replies: 15
- Views: 7457
Re: Cam tools.
Deleted
- Mon Jul 18, 2022 3:32 am
- Forum: Tools
- Topic: Cam tools.
- Replies: 15
- Views: 7457
Re: Cam tools.
Deleted
- Sun Jun 19, 2022 6:35 pm
- Forum: General Discussions
- Topic: Fuel range
- Replies: 3
- Views: 493
Re: Fuel range
Deleted
- Tue Jun 14, 2022 11:26 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Torque Setting
- Replies: 3
- Views: 825
Re: Torque Setting
Deleted