Search found 93 matches

by Boxflyer
Mon Mar 18, 2024 8:55 pm
Forum: Maintenance, Servicing and Problems
Topic: Which Fairing Bolts
Replies: 22
Views: 4108

Re: Which Fairing Bolts

There are 3 screws that are longer without shoulders in each engine fairing starting with the 2019 and usually no screw on the tank cover forward point under the each side glove box. On the Torque Sheet, the new value for the rear Brake Caliper is 28Nm vs 24Nm. I may make a completely NEW version of...
by Boxflyer
Mon Feb 26, 2024 2:28 pm
Forum: Maintenance, Servicing and Problems
Topic: Brake Fluid
Replies: 6
Views: 345

Re: Brake Fluid

It is actually DOT4 LV (Low Viscosity). This is what is specified now for bikes back as far as early 1990’s R-series as well as others. What’s stamped on the reservoir cap won’t be updated, but specifications from BMW are changed from time to time. You can keep up to date with your particular model ...
by Boxflyer
Wed Dec 20, 2023 10:41 pm
Forum: Maintenance, Servicing and Problems
Topic: Body panel screws
Replies: 7
Views: 1381

Re: Body panel screws

Looks like a solution.
by Boxflyer
Mon Jul 24, 2023 1:18 pm
Forum: Maintenance, Servicing and Problems
Topic: Which Fairing Bolts
Replies: 22
Views: 4108

Re: Which Fairing Bolts

If you have a WetHead 1200, this shop aid will help. It keeps your screws from being lost and reminds you of not putting back all the screws and where they should go if you have some left over on reassembly. I take this file to my local FedEx Office printing location and have them print it out 12x18...
by Boxflyer
Sun Jul 23, 2023 10:30 am
Forum: Maintenance, Servicing and Problems
Topic: 12,000 mile service due
Replies: 11
Views: 955

Re: 12,000 mile service due

Gavj wrote: Sun Jul 23, 2023 9:23 am Im not finding a lot on youtube re checking vaves etc....
Here's some info on checking VALVES.
https://youtu.be/PQeNcD0gGOw

Image
by Boxflyer
Tue Jul 18, 2023 9:29 pm
Forum: Maintenance, Servicing and Problems
Topic: Valve clearance
Replies: 10
Views: 1269

Re: Valve clearance

With the range being 0.10mm for both the Intake and Exhaust, and the hemispherical shims only available in 0.05mm spacing...that means that only 1 size shim will put in the range...a second incremental step in shims will put you outside the acceptable area the other way. Hope that makes sense and an...
by Boxflyer
Mon Jul 17, 2023 3:48 pm
Forum: Maintenance, Servicing and Problems
Topic: Valve clearance
Replies: 10
Views: 1269

Re: Valve clearance

The procedure for doing the Cam Timing on the 1200 CamHead engine is very similar to what I do frequently on the 1200/1250 WetHead/ShiftHead. You need to set and lock the flywheel/crankshaft at TDC with a specific pin that fits in an open hole on the RH side of the rear of the engine block. The side...
by Boxflyer
Mon Jul 03, 2023 2:03 pm
Forum: Maintenance, Servicing and Problems
Topic: Valve clearance
Replies: 10
Views: 1269

Re: Valve clearance

I would change 5 of the 8 shims. Both of the 0.41mm clearance EXH. valves would be set to a good value of 0.36mm. The other EXH now at 0.38mm would be at 0.33mm, making it nearer to the tighter end of the range. Of course the 0.23mm INT would be at 0.18mm, a reasonable number closer to the middle an...
by Boxflyer
Mon Jul 03, 2023 2:08 am
Forum: Maintenance, Servicing and Problems
Topic: Valve clearance
Replies: 10
Views: 1269

Re: Valve clearance

I would say that if it's outside the specification, it should be adjusted...if it's at the limit of the spec, and you are already replacing some of the shims to replace the one that's at 0.23mm as well. If money was not a factor, I'd put all of the clearances at 1/3 of the range of tolerances. So fo...
by Boxflyer
Mon Jun 12, 2023 3:13 pm
Forum: Maintenance, Servicing and Problems
Topic: 1250 Caliper bolt torque
Replies: 3
Views: 664

Re: 1250 Caliper bolt torque

Direct from the Updateable Repair Manual R Models K5X Official DVD (not a copy): Radial brake caliper on telescopic forks (M10x65 bolt) 38NM (Note: no mention of using thread locker) Brake caliper to bevel gears (Long threaded dome to bevel gears M8x30 bolts) 28Nm Replace screw. Thread-locking compo...
by Boxflyer
Mon Oct 17, 2022 1:49 pm
Forum: Newbies
Topic: New R1200RT Owner
Replies: 7
Views: 534

Re: New R1200RT Owner

Deleted
by Boxflyer
Wed Aug 17, 2022 2:36 pm
Forum: Tools
Topic: Cam tools.
Replies: 15
Views: 4776

Re: Cam tools.

Deleted
by Boxflyer
Mon Jul 18, 2022 3:32 am
Forum: Tools
Topic: Cam tools.
Replies: 15
Views: 4776

Re: Cam tools.

Deleted
by Boxflyer
Sun Jun 19, 2022 6:35 pm
Forum: General Discussions
Topic: Fuel range
Replies: 3
Views: 463

Re: Fuel range

Deleted
by Boxflyer
Tue Jun 14, 2022 11:26 pm
Forum: Maintenance, Servicing and Problems
Topic: Torque Setting
Replies: 3
Views: 717

Re: Torque Setting

Deleted