Dealing with corrosion!

Having Problems with your BMW R1200RT/R1250RT? or have some Maintenance and Service questions?
burridge01
Posts: 559
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: Modified "16" R1200RT
Been liked: 192 times
Great Britain

Re: Dealing with corrosion!

Post by burridge01 »

sakm wrote: Tue Jan 10, 2023 7:54 pm Thats what I was planning on using :)
Never been defeated using it yet and I've pulled the odd spring or 2.
User avatar
David.
Subscriber
Posts: 8007
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 332 times
Great Britain

Re: Dealing with corrosion!

Post by David. »

If it's that easy with a spring puller, why are the guys in the videos messing about with washers and ratchet straps.
User avatar
sakm
Administrator
Posts: 1301
Joined: Wed Jun 02, 2021 9:13 pm
Location: Hull, UK
Bike Model and Year: 2016 R1200RT
Has liked: 436 times
Been liked: 388 times
Great Britain

Re: Dealing with corrosion!

Post by sakm »

David. wrote: Tue Jan 10, 2023 10:03 pm If it's that easy with a spring puller, why are the guys in the videos messing about with washers and ratchet straps.
A lot of it is technique

And they won't have a spring puller :lol:

You will be surprised how easy it is with the right tool
User avatar
David.
Subscriber
Posts: 8007
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 332 times
Great Britain

Re: Dealing with corrosion!

Post by David. »

In the Normski video, the spring is measured as needing to be stretched by 32mm to fit it. Later, the spring can be seen with one end held in a vice while a screwdriver is used double handed to try and stretch the spring. He can only get a few mm of movement, no where near the 32mm required.

All other comments viewed elsewhere use the washer method, inc. for the RT style double spring set up with connecting plates.
burridge01
Posts: 559
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: Modified "16" R1200RT
Been liked: 192 times
Great Britain

Re: Dealing with corrosion!

Post by burridge01 »

David. wrote: Tue Jan 10, 2023 10:03 pm If it's that easy with a spring puller, why are the guys in the videos messing about with washers and ratchet straps.
Maybe it's a little to hard for them David.Some of us are stronger than others :mrgreen: .
As I've said earlier,I will use the washers for spacing,if they go in easy enough,or I'll put a bit of effort in and use the spring puller :thumb:
User avatar
David.
Subscriber
Posts: 8007
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 332 times
Great Britain

Re: Dealing with corrosion!

Post by David. »

Found this on the R1200R Forum, https://www.r1200rforum.com/threads/cen ... ngs.53383/

"This gadget that I made makes it very easy to take the stand off. With the bike on side stand the pegs are pushed into the spring hanger plates. Then the centre-stand is pushed down towards the ground to extend the spring. While its in that position the yellow plated nut is spun down to take up the slack. Then lift the stand and take the whole lot off the hanger pegs on stand and frame. Leave it at that tension till its time to refit."

Image Image
User avatar
Doctor T
Posts: 1624
Joined: Tue Dec 21, 2021 10:21 pm
Location: west sussex
Bike Model and Year: 2007 R1200RT SE
Has liked: 878 times
Been liked: 230 times
Great Britain

Re: Dealing with corrosion!

Post by Doctor T »

Bet you are glad you haven't a 2006 to 2009 RT. These are known for bad paintwork on metal surfaces. My wheels are terrible and the places on the frame ain't much better. Am going to sort the wheels out but sod the frame, there is just too much to remove to get it down where i can clean and respray it. I cleaned up my center stand without removing it. The springs on my bike have a rubber sleeve covering them. I used a Dremel with a wire wool disc and a sanding disc on the larger areas, painted it with a rust converter, rubbed it down again, and then sprayed 3 coats of Hammerite smooth satin black. Now looks much better than the scab looking piece of metal. Sidestand got the same procedure.
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
User avatar
David.
Subscriber
Posts: 8007
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 332 times
Great Britain

Re: Dealing with corrosion!

Post by David. »

Centre stands do get hammered with gravel rash, (particularly the crossbar between the two vertical legs), resulting in corrosion. Not wishing to remove the stand, I rubbed down the horizontal tube, brush painted with Hammerite Smooth then fitted a length of plastic tubing for future protection.

Image Image

On this RT with a mud flap attached to the sump, the centre stand is in good condition.

Image
User avatar
Doctor T
Posts: 1624
Joined: Tue Dec 21, 2021 10:21 pm
Location: west sussex
Bike Model and Year: 2007 R1200RT SE
Has liked: 878 times
Been liked: 230 times
Great Britain

Re: Dealing with corrosion!

Post by Doctor T »

What a good idea.
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
User avatar
sakm
Administrator
Posts: 1301
Joined: Wed Jun 02, 2021 9:13 pm
Location: Hull, UK
Bike Model and Year: 2016 R1200RT
Has liked: 436 times
Been liked: 388 times
Great Britain

Re: Dealing with corrosion!

Post by sakm »

David. wrote: Wed Jan 11, 2023 10:31 am
Image Image

Removed the centre stand today and stripped it ready for powder coating!

I think I will be making one of these! those bloody springs are strong :shock:
Panman40
Posts: 325
Joined: Tue Mar 22, 2022 8:46 pm
Has liked: 257 times
Been liked: 33 times
Great Britain

Re: Dealing with corrosion!

Post by Panman40 »

That’s a great idea!, which finish are you going for, satin or gloss black ?
User avatar
David.
Subscriber
Posts: 8007
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 332 times
Great Britain

Re: Dealing with corrosion!

Post by David. »

sakm wrote: Sun Feb 05, 2023 6:47 pmI think I will be making one of these, those springs are strong.
Image
sakm wrote: Tue Jan 10, 2023 7:54 pmWhat I was planning on using.
Image
burridge01 wrote: Tue Jan 10, 2023 8:08 pmNever been defeated using it yet and I've pulled the odd spring or 2.
User avatar
sakm
Administrator
Posts: 1301
Joined: Wed Jun 02, 2021 9:13 pm
Location: Hull, UK
Bike Model and Year: 2016 R1200RT
Has liked: 436 times
Been liked: 388 times
Great Britain

Re: Dealing with corrosion!

Post by sakm »

That's what I used and wasn't defeated! I won and got the springs off but it was hard work

I'm looking at the easy route and working smarter not harder 😉
User avatar
David.
Subscriber
Posts: 8007
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 332 times
Great Britain

Re: Dealing with corrosion!

Post by David. »

David. wrote: Tue Jan 10, 2023 10:03 pmIf it's that easy with a spring puller, why are the guys in the videos messing about with washers and ratchet straps.
Here's another method.

burridge01
Posts: 559
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: Modified "16" R1200RT
Been liked: 192 times
Great Britain

Re: Dealing with corrosion!

Post by burridge01 »

David,why have you quoted me.
Post Reply