hex can and Innovv V3 camera

Got any tips and tricks for BMW R1200RT/R1250RT owners? feel free to share them here.
Post Reply
User avatar
exportman
Posts: 287
Joined: Tue Sep 27, 2016 7:57 pm
Bike Model and Year: R1250RT 2023
Has liked: 6 times
Been liked: 40 times
Great Britain

hex can and Innovv V3 camera

Post by exportman »

Hi
Thought I would share how I have fixed my Hexcan and Innovv Camera on my new 1250

The hexcan is under the tail of the pillion seat. the supplied positive and negative are just about long enough to reach the battery terminal on the right hand side of the bike and used the redundant TPM connector under the rack and advised by innovv to connect to the canbus
hexcan.jpg
hexcan.jpg (346.95 KiB) Viewed 946 times
The Innovv I had wired up before getting the hexcan so the switched supply for that taps into the rear aux socket again the main power is from the battery terminals on the right of the bike. The VR unit is between the tank and the rider seat secured with 3M dual lock tape
innovv recorder.jpg
innovv recorder.jpg (375.39 KiB) Viewed 946 times
Front camera is secured on the right hand clear wind deflector ( UK so off side) using 2 x L pieces from the fittings kit to clamp to the plastic along with a DIY silicon stick in button cut in half just to add some stability and security
front camera.jpg
front camera.jpg (282.66 KiB) Viewed 946 times
Rear camera again some dual lock and for extra safety zip ties under the rear of the rack.
rear camera.jpg
rear camera.jpg (323.65 KiB) Viewed 946 times
The remote is on the right hand infill panel again with dual lock
remote.jpg
remote.jpg (315.59 KiB) Viewed 946 times
finally the GPS sensor is on the tail just under the rack near the rear light

SO far the hexcan is powering an additional stop light and a tomtom satnav may add some additional spot lights but thats for another day maybe
User avatar
Doctor T
Posts: 1624
Joined: Tue Dec 21, 2021 10:21 pm
Location: west sussex
Bike Model and Year: 2007 R1200RT SE
Has liked: 878 times
Been liked: 230 times
Great Britain

Re: hex can and Innovv V3 camera

Post by Doctor T »

Very tidy insulation. :thumb:
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
User avatar
exportman
Posts: 287
Joined: Tue Sep 27, 2016 7:57 pm
Bike Model and Year: R1250RT 2023
Has liked: 6 times
Been liked: 40 times
Great Britain

Re: hex can and Innovv V3 camera

Post by exportman »

Hi

No too bad all the cabling is secured behind the panelling nothing drilled all removable when (if) I change bike again.
I should add make sure if installing this way you leave enough give on the cables to lift the VR Unit clear of the seat bobbins so you can remove the Micro SD card.
Much neater installation than I did on my previous RT.
Glenn
Posts: 251
Joined: Sat Jan 15, 2022 7:49 pm
Location: Shropshire
Bike Model and Year: R1250RT LE 2018
Has liked: 18 times
Been liked: 83 times
Great Britain

Re: hex can and Innovv V3 camera

Post by Glenn »

I have my front camera mounted under the headlight
Attachments
PXL_20230304_160751699.jpg
PXL_20230304_160751699.jpg (381.41 KiB) Viewed 916 times
Casbar
Posts: 2670
Joined: Wed Jan 27, 2016 6:25 am
Been liked: 45 times
Great Britain

Re: hex can and Innovv V3 camera

Post by Casbar »

I also have mine under the headlamp using the go pro bracket. Not sure if that fits 21 on bikes though.
Post Reply