JB Weld,,,,,,,or

General discussion of the BMW R1200RT/R1250RT
Post Reply
burridge01
Posts: 586
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: Modified "16" R1200RT
Been liked: 194 times
Great Britain

JB Weld,,,,,,,or

Post by burridge01 »

Anyone use an off the shelf epoxy that's stronger than JB Weld.Ive found Systemthree 88,but it's expensive for what I want.
The replacement lug on the side panel has again detached itself :roll: Last time I used JB quick,not realising normal JB is almost twice as strong.As it stands I'm looking at JB again,unless someone has a better suggestion :thumb:

Should add,this is needed for plastic to alloy/metal.
Top
User avatar
EasyRider
Subscriber
Posts: 605
Joined: Tue Nov 21, 2023 7:27 am
Location: South Wales
Bike Model and Year: 2019 R1250RT LE
Has liked: 90 times
Been liked: 165 times
Wales

Re: JB Weld,,,,,,,or

Post by EasyRider »

JB Weld is good stuff and good value. I always keep some here for them just in case times.
Dont Ride Faster, Than Your Angel Can Fly. :thumb:
Top
User avatar
Doctor T
Posts: 1673
Joined: Tue Dec 21, 2021 10:21 pm
Location: west sussex
Bike Model and Year: 2007 R1200RT SE
Has liked: 911 times
Been liked: 239 times
Great Britain

Re: JB Weld,,,,,,,or

Post by Doctor T »

An easy fix for plastic is melted cable ties. Soldering lron to melt the ties. Used this trick may time on Jap panels
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
Top
Glenn
Posts: 283
Joined: Sat Jan 15, 2022 7:49 pm
Location: Shropshire
Bike Model and Year: R1250RT LE 2018
Has liked: 28 times
Been liked: 92 times
Great Britain

Re: JB Weld,,,,,,,or

Post by Glenn »

Doctor T wrote: ↑Sun Mar 31, 2024 1:35 pm An easy fix for plastic is melted cable ties. Soldering lron to melt the ties. Used this trick may time on Jap panels
A glue gun works well with cable ties too
Top
burridge01
Posts: 586
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: Modified "16" R1200RT
Been liked: 194 times
Great Britain

Re: JB Weld,,,,,,,or

Post by burridge01 »

That's not going to work on the panel lugs.
Top
Beem530i
Posts: 15
Joined: Tue Feb 14, 2023 4:26 pm
Bike Model and Year: RT 2018
Has liked: 1 time
Been liked: 5 times
United States of America

Re: JB Weld,,,,,,,or

Post by Beem530i »

If by "panel lugs" you mean the two little plastic tabs that hold the top fairings in place and fit into little slots, Clearwater lights makes self-adhesive metal replacements you may want to check out.

https://www.clearwaterlights.com/produc ... ter-cooled

They are not cheap but worked on my 2014 RT

If I have totally misconstrued what a "panel lug" is I beg your forgiveness!
Top
burridge01
Posts: 586
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: Modified "16" R1200RT
Been liked: 194 times
Great Britain

Re: JB Weld,,,,,,,or

Post by burridge01 »

No,you are right and I did buy some of there replacement tabs(cost a fortune with the postage shipped to the UK)I stuck them on along with JB QUICK weld but on a Spanish/Portugal tour last year they came unstuck in the heat(42c in some parts of Spain)and speed of the bike on motorways.So they are precisely what I am attempting to reapply.
Have now stuck them back on with original JB weld(24hr cure)I'm putting some fibreglass over the top and to finish of some strips of 3M dual lock.
I really can't see anymore I can do.
Thanks for the suggestion :cheers:
Top
Post Reply

Return to “General Discussions”