linked brakes
-
Doctor T
- Posts: 2299
- Joined: Tue Dec 21, 2021 10:21 pm
- Location: west sussex
- Bike Model and Year: 2007 R1200RT SE
- Has liked: 1440 times
- Been liked: 409 times
linked brakes
When did linked brakes come in and what models have it?.
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
May the shaft be with you
May the shaft be with you
-
David.
- Posts: 8632
- Joined: Fri Nov 07, 2014 7:29 pm
- Location: North Yorkshire
- Bike Model and Year: R1200RT (Camhead) 2012
- Been liked: 478 times
Re: linked brakes
Don't know when linked brakes were first introduced but both Hexheads (2007) and Camheads (2012) have them.
Last edited by David. on Tue Feb 22, 2022 6:00 pm, edited 1 time in total.
-
Doctor T
- Posts: 2299
- Joined: Tue Dec 21, 2021 10:21 pm
- Location: west sussex
- Bike Model and Year: 2007 R1200RT SE
- Has liked: 1440 times
- Been liked: 409 times
Re: linked brakes
So my 2007 Hexhead should have then. How can i test them to see if they work?
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
May the shaft be with you
May the shaft be with you
-
David.
- Posts: 8632
- Joined: Fri Nov 07, 2014 7:29 pm
- Location: North Yorkshire
- Bike Model and Year: R1200RT (Camhead) 2012
- Been liked: 478 times
Re: linked brakes
Pull the front handbrake lever only and see if any braking force is applied to the rear wheel.Doctor T wrote:How can I test them to see if they work.
Last edited by David. on Tue Feb 22, 2022 6:56 pm, edited 1 time in total.
-
Doctor T
- Posts: 2299
- Joined: Tue Dec 21, 2021 10:21 pm
- Location: west sussex
- Bike Model and Year: 2007 R1200RT SE
- Has liked: 1440 times
- Been liked: 409 times
Re: linked brakes
On my last ride, i did feel like both brakes were working when i used only the front lever. My old 2007 must have had the same but i forget the feeling of both brakes working. Funny there are no YT videos showing or explaining this.
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
May the shaft be with you
May the shaft be with you
-
Our Gee
- Posts: 800
- Joined: Sun Nov 08, 2015 7:43 am
- Location: North Yorkshire UK
- Bike Model and Year: R1200RT 2011
- Been liked: 33 times
Re: linked brakes
David. wrote: Pull the front handbrake lever only and see if any braking force is applied to the rear wheel.
To do this check I believe you will need to have the ignition switched on, although when I tried it there where some rather unpleasant sounds emitted from under the tank !!.
Last edited by Our Gee on Wed Feb 23, 2022 7:26 am, edited 1 time in total.
-
David.
- Posts: 8632
- Joined: Fri Nov 07, 2014 7:29 pm
- Location: North Yorkshire
- Bike Model and Year: R1200RT (Camhead) 2012
- Been liked: 478 times
Re: linked brakes
Yes, with the ignition switched on, the ABS motor/pump will be activated to control the braking system.
-
Our Gee
- Posts: 800
- Joined: Sun Nov 08, 2015 7:43 am
- Location: North Yorkshire UK
- Bike Model and Year: R1200RT 2011
- Been liked: 33 times
Re: linked brakes
Randyjaco wrote: As OP asked, what models have it?
David has given some info but if further details are required you might just have to do some research.
-
simbo
- Subscriber
- Posts: 1575
- Joined: Fri Sep 16, 2016 10:33 pm
- Location: Greater Manchester
- Bike Model and Year: RT 2011
- Has liked: 101 times
- Been liked: 232 times
Re: linked brakes
Randyjaco wrote: As OP asked, what models have it?
All RT models have linked brakes dating back to the R1150rt from around 2000 onwards.
-
Doctor T
- Posts: 2299
- Joined: Tue Dec 21, 2021 10:21 pm
- Location: west sussex
- Bike Model and Year: 2007 R1200RT SE
- Has liked: 1440 times
- Been liked: 409 times
Re: linked brakes
I suspect it refers to RS, R models as well within these years. One article i read said it only works from 30 mph upwards. Under that, it's normal brakes. K bikes is different. Their link brake system works at any speed
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
May the shaft be with you
May the shaft be with you