Search found 375 matches
- Sun Jun 02, 2024 6:08 am
- Forum: Clothing
- Topic: Neck tube ?
- Replies: 0
- Views: 24
Neck tube ?
Ok so I suffer with a bad neck most of the time, wear n tear. I’m trying to find a summer ish neck tube that is shaped not just a straight buff type thing. I’d like something that sits down the back of my neck better to keep droughts out , my plain summer neck buff tends to just bunch and ride up. I...
- Sun Jun 02, 2024 6:02 am
- Forum: General Discussions
- Topic: Shoei neotec 2 brain surgery lines ?
- Replies: 2
- Views: 69
- Sun Jun 02, 2024 6:00 am
- Forum: Clothing
- Topic: Summer mesh jacket that’s waterproof ?
- Replies: 30
- Views: 4933
Re: Summer mesh jacket that’s waterproof ?
Just a quick update on the Oxford jacket, I’ve probably worn it 5 or so times this season and have found a hole about 1 cm in the inside chest pocket which is where I put my phone, the case has smooth rounded corners 🤨, the pockets are a thin mesh type material, I’m a bit disappointed tbh!, I’ve sen...
- Sat Jun 01, 2024 9:24 pm
- Forum: General Discussions
- Topic: Shoei neotec 2 brain surgery lines ?
- Replies: 2
- Views: 69
Shoei neotec 2 brain surgery lines ?
Ok so anyone else with a shoei neotec 2 without hair get this lobotomy type mark on the forehead from the line of stitching ?
- Fri May 31, 2024 7:05 am
- Forum: General Discussions
- Topic: Heightened seat & lowered pegs experiences?
- Replies: 8
- Views: 1451
Re: Heightened seat & lowered pegs experiences?
Ah great, , I think the brake side comes with a plate to lower it so should be fine.burridge01 wrote: ↑Thu May 30, 2024 8:31 am Plenty of adjustment in the lever.I had to extend the lever out to make it more comfortable but that is easy to do
- Thu May 30, 2024 5:32 am
- Forum: General Discussions
- Topic: Heightened seat & lowered pegs experiences?
- Replies: 8
- Views: 1451
Re: Heightened seat & lowered pegs experiences?
Well I’ve ordered the lowering kit from aliexpress, I’m just hoping there’s enough adjustment in the gear lever to get a comfortable position and still be able to change gear!. I’ll do that side first I think.
- Wed May 29, 2024 9:38 pm
- Forum: Aftermarket Parts & Accessories
- Topic: z technik v stream
- Replies: 7
- Views: 1313
Re: z technik v stream
thanks for the link David. Sakm, my screen is a big one..its 720mm in length. it is brilliant for wind reduction. had it on my r1250rt 2019 model. it does get a bit warm if you are abroad to be honest but the benefits of no buffeting and no noise makes up for it/ you can ride at 85mph with your vis...
- Sat May 25, 2024 10:10 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
Re: Lever plunger ?
Could the thread on the plunger be dressed up using a die. The grub screw in the barrel could be drilled out and threads re-tapped, together with the thread for the plunger. Or, drill out both threads and fit Time-Serts to repair the threads. Alternatively, have a new barrel manufactured. All good ...
- Sat May 25, 2024 9:16 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
Re: Lever plunger ?
I'm confused (easily done), were the plungers removed without removing the grub screws, then screwed back in. Yes, when I went to tighten the brake grub screw after threading in the plunger it was stuck fast and rounded out the hex. As it happened the thread on the plunger was a little burred so lo...
- Sat May 25, 2024 9:02 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
Re: Lever plunger ?
Yes, but I couldn’t remove the locking ones, I should of left it at a half turn really it’s a very strange setup to be honest.
- Sat May 25, 2024 8:13 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
- Sat May 25, 2024 8:10 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
Re: Lever plunger ?
Both!, are you thinking drill them out and try and re tap the threads ?.David. wrote: ↑Sat May 25, 2024 7:20 pm Is it the plunger adjuster or grub screw in the barrel which is rounded out.
Plunger.JPG
If it's the grub screw, this might do the trick, https://a2stainless.co.uk/product/m4-x- ... in-914-a2/
- Sat May 25, 2024 1:00 pm
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
- Sat May 25, 2024 7:49 am
- Forum: Maintenance, Servicing and Problems
- Topic: Lever plunger ?
- Replies: 15
- Views: 1313
Lever plunger ?
So after swapping my levers over I managed to mess up the tiny 2mm Allen grub screws you have to loosen ( covered in red threadlock) , I thought each part could be purchased separately having read another forum but the dealer said unlikely as it looks like that plunger rod is part of the master cyli...
- Sun May 19, 2024 10:55 pm
- Forum: Aftermarket Parts & Accessories
- Topic: Aftermarket levers
- Replies: 17
- Views: 5307